Dear Sirs, Pls. tell me what criteria to be considered when selecting safety shoes for metal working industries and chemical industries. Thanks in advance. Regards, SSM
From India, Madras
Acknowledge(0)
Amend(0)
47From India, Madras
Acknowledge(0)Amend(0)
Please go through the attachment; it may be helpful to you. For any technical details or assistance in selecting suitable safety footwear, you may contact RAHMAN INDUSTRIES LTD. They are the manufacturers of safety footwear under the brand name of Safetix, primarily exporting to European countries.
Regards.
From India
Acknowledge(0)Amend(0)
Regards.
From India
Acknowledge(0)Amend(0)
Dear SSM, Please find the attached safety shoes selection documents hope its helps. . . Source:Internet Dear Dipil Nice one about safety shoes.Thanks a lot. . . Keep on sharing. . .
From United States, Fpo
Acknowledge(0)Amend(0)
From United States, Fpo
Acknowledge(0)Amend(0)
Requirements for Chemical Units
For the chemical industry, you have to conduct a survey along the following lines:
- Write down the names of the chemicals that are being used/manufactured in the factory.
- Ascertain whether the chemical is confined to the floor (requires chemical-resistant sole) or if it is also likely to cause splashes on the footwear (in such cases, you need chemical-resistant upper).
- Electrical Hazard: I advise you to opt for antistatic footwear, as electrical hazard footwear can ignite inflammable chemicals.
- You have to choose the appropriate sole material that can withstand the chemicals used in your workplace. There is a chart available for this, which I have on hand.
- If there are broken pieces of glass on the shop floor, you will require a steel midsole in addition to a steel toe cap.
Requirements for Metalworking Units
In metalworking units, you need safety footwear with a steel toe cap and steel midsole. If there are hot areas above 150 degrees Celsius and below 300 degrees Celsius, you need a vulcanized Nitrile rubber sole. Otherwise, a PU sole will work.
I have corrected the spelling, grammar, and formatting of the text to improve clarity and readability. Let me know if you need further assistance.
Regards
From India, Kanpur
Acknowledge(0)Amend(0)
For the chemical industry, you have to conduct a survey along the following lines:
- Write down the names of the chemicals that are being used/manufactured in the factory.
- Ascertain whether the chemical is confined to the floor (requires chemical-resistant sole) or if it is also likely to cause splashes on the footwear (in such cases, you need chemical-resistant upper).
- Electrical Hazard: I advise you to opt for antistatic footwear, as electrical hazard footwear can ignite inflammable chemicals.
- You have to choose the appropriate sole material that can withstand the chemicals used in your workplace. There is a chart available for this, which I have on hand.
- If there are broken pieces of glass on the shop floor, you will require a steel midsole in addition to a steel toe cap.
Requirements for Metalworking Units
In metalworking units, you need safety footwear with a steel toe cap and steel midsole. If there are hot areas above 150 degrees Celsius and below 300 degrees Celsius, you need a vulcanized Nitrile rubber sole. Otherwise, a PU sole will work.
I have corrected the spelling, grammar, and formatting of the text to improve clarity and readability. Let me know if you need further assistance.
Regards
From India, Kanpur
Acknowledge(0)Amend(0)
Please find a small contribution from my side.
Dear Dipil and Ragu,
Thank you for your excellent presentation. In addition to that, please note the following while selecting:
- Density: 500 to 530 kg/m³.
- Abrasion: on a volume basis < 250 n.m³, on a weight basis < 150 mg.
Regards
From India, Delhi
Acknowledge(0)Amend(0)
Dear Dipil and Ragu,
Thank you for your excellent presentation. In addition to that, please note the following while selecting:
- Density: 500 to 530 kg/m³.
- Abrasion: on a volume basis < 250 n.m³, on a weight basis < 150 mg.
Regards
From India, Delhi
Acknowledge(0)Amend(0)
Dear all, One more nice/worth PPT related to Foot protection. . . Hope its helps. . . Keep on sharing. . .
From United States, Fpo
Acknowledge(0)Amend(0)
From United States, Fpo
Acknowledge(0)Amend(0)
@ Chuknoo Thanks a lot for your inputs into the thread.
Dear SSM, While selecting the footwear, you may go ahead with what Chuknoo advised. If you can do the survey he suggested and come back to the forum with your specific result of the survey, you will be guided to find specific footwear by him.
@ All In the name of Chuknoo, we have a senior member, Dr. Sudhir Agarwal, who is an expert in the field of Safety Footwear Manufacturing. Let's welcome him to the forum in a grand way and utilize his expertise in delivering the right foot protection to our colleagues. He is a very helpful person. Thank you for joining citehr, and we look forward to learning a lot from you.
Keep on sharing and keep up the pace.
Regards
From India
Acknowledge(0)Amend(0)
Dear SSM, While selecting the footwear, you may go ahead with what Chuknoo advised. If you can do the survey he suggested and come back to the forum with your specific result of the survey, you will be guided to find specific footwear by him.
@ All In the name of Chuknoo, we have a senior member, Dr. Sudhir Agarwal, who is an expert in the field of Safety Footwear Manufacturing. Let's welcome him to the forum in a grand way and utilize his expertise in delivering the right foot protection to our colleagues. He is a very helpful person. Thank you for joining citehr, and we look forward to learning a lot from you.
Keep on sharing and keep up the pace.
Regards
From India
Acknowledge(0)Amend(0)
The Key to Safety Shoes and Boots
The key to safety shoes and boots is asking two questions: What standards are recognized in your part of the world, and what is available to your workers? Not all safety shoes meet the job requirements.
CSA green triangle boots and shoes are okay, but depending on the chemical standards, they may need certain other ratings to fully protect the workers' feet.
The second consideration is that metal workers have a second rating put on their feet for safety, with an upper shield or faceplate put on the laces. Always lace the boots military style so they can be taken off or cut off quickly if the foot is crushed, which is crucial for first aid requirements.
Last but not least, they protect a valuable feature of your body, so it's like asking, "Do I buy cheap or expensive?" The key is buying to protect, which is a better answer.
This link shows the minimum standards we need in Canada, but the key is what the standard is in your government legislation for your workers: OSH Answers: Safety Footwear
Proper foot safety is important to all of us. Your feet take an enormous amount of punishment in everyday living, not to mention working in a cluttered garage or workshop. It is only common sense to wear footwear fitting for the job. You wouldn't wear sandals outside in the winter, nor would you in a shop.
There are all kinds of styles for the fashion-conscious. There are the ones that look like the typical high-cut safety boots to ones looking like cowboy boots. Then there are the ones that are low-cut standard look-alike shoes. There are even ones that you can use as dress shoes. The important thing is to wear them.
In designing strategies to protect against foot injury, one has to remember the fundamental principle of occupational health and safety: that occupational hazards should be eliminated at the source. The role of personal protective equipment is to minimize exposure to specific occupational hazards, not to eliminate them. Protective footwear does not guarantee total protection.
The best defense against injuries is prevention. A clean workplace is number one on the scale:
- Clear the work floor of any sharp, hot objects that can penetrate your safety footwear.
- Clear any walking paths of any obstacles that can scrape the side of your feet or ankles.
- Avoidance of obstacles can cause twisting or spraining of feet and ankles.
- Safely secure any objects above the floor from falling on your feet.
- Make sure the floor and paths have proper resistance for walking. A newly painted floor can be like layering ice on the floor. Putting sand or other material in with the paint will ensure some resistance to slippage.
All jurisdictions require that workers wear adequate protection against workplace hazards. All working footwear, for both men and women, whether it is safety wear or not, should provide comfort without compromising protective value.
Basic Things to Look for in Buying Safety Footwear
- A steel toe cap should cover the whole length of the toes from tips to beyond the natural bend of the foot. A soft pad covering the edge of the toecap increases comfort. If the toecap cuts into the foot, either the size or style of the footwear is incorrect.
- Soles come in a variety of thicknesses and materials. They need to be chosen according to the hazards and type(s) of flooring in the workplace.
- Uppers of protective footwear come in a variety of materials. Selection should take into account the hazards and individual characteristics of the worker's foot.
- A steel midsole, which protects the foot against penetration by sharp objects, should be flexible enough to allow the foot to bend.
- No one type of non-slip footwear can prevent the wearer from slipping on every surface type.
- Make sure they are a good fit.
There are conditions such as calluses, ingrown toenails, or simply tired feet that are common among workers. Although these may not be considered occupational injuries in the strictest sense, they can have serious consequences for health and safety at the workplace. They cause discomfort, pain, and fatigue. Fatigue sets up the worker for further injuries affecting the muscles and joints. Also, a worker who is tired and suffering pain is less alert and more likely to act unsafely. An accident of any kind may result. A proper fitting boot will also help in good posture and skeletal alignment.
Fit and Care of Safety Footwear
Check the Fit:
- Walk in the new footwear to ensure it is comfortable.
- Boots should have ample toe room (toes should be about 12.5 mm from the front).
- Make allowances for extra socks or special arch supports when buying boots.
- Boots should fit snugly around the heel and ankle when laced.
- Lace up boots fully. High-cut boots provide support against ankle injury. Loose laces can be a hazard in themselves, causing tripping over your own feet or catching on objects in the area.
Footwear Care:
- Use a protective coating to make footwear water-resistant. Inspect and reapply protective coating when necessary. Wet boots often curl near the toe when dried, causing discomfort and abnormal wear.
- Inspect footwear regularly for damage. The soles often crack with age, leaving openings for potential hazards.
- Repair or replace worn or defective footwear.
- Electric shock resistance of footwear is greatly reduced by wet conditions and with wear. Dig out any objects stuck in the sole. They can make the boot a path for electricity and a slippery factor on the floor.
Boot Badges on the Boots
Boot badges will signify the level of safety the boot will have.
Selection of Safety Footwear
Marking Criteria Use
- Green triangle footwear has sole puncture protection with a Grade 1 protective toe (withstand impact up to 125 joules).
- Any industrial or heavy work environment, including construction, where sharp objects are present (such as nails).
- Yellow triangle footwear has sole puncture protection and Grade 2 protective toe (withstand impact up to 90 joules).
- Light industrial work environments that need both puncture and toe protection.
- White rectangle with orange Greek letter "omega" footwear has soles that provide electric shock resistance.
- Any industrial environment where accidental contact with live electrical conductors can occur. (REMEMBER: Electric shock resistance is greatly reduced by wet conditions and with wear)
- Yellow rectangle with green letters "SD" and grounding symbol footwear has soles that are static dissipative.
- Any industrial environment where a static discharge can be a hazard for workers or equipment.
- Red rectangle with black letter "C" and grounding symbol footwear has soles that are electrically conductive.
- For any industrial environment where low-power electrical charges can be a hazard for workers or equipment.
- White label with green fir tree symbol footwear provides protection when using chainsaws.
- For forestry workers and others who work with or around hand-held chainsaws and other cutting tools.
Note 1: The ® symbol indicates the preferred position for the identifying logo or mark of the certifying agency.
Note 2: Labels are on the tongue of the right shoe at ankle height. They may also appear at ankle height on the shoe itself (for electrical protection footwear).
Regards
From Canada, Calgary
Acknowledge(0)Amend(0)
The key to safety shoes and boots is asking two questions: What standards are recognized in your part of the world, and what is available to your workers? Not all safety shoes meet the job requirements.
CSA green triangle boots and shoes are okay, but depending on the chemical standards, they may need certain other ratings to fully protect the workers' feet.
The second consideration is that metal workers have a second rating put on their feet for safety, with an upper shield or faceplate put on the laces. Always lace the boots military style so they can be taken off or cut off quickly if the foot is crushed, which is crucial for first aid requirements.
Last but not least, they protect a valuable feature of your body, so it's like asking, "Do I buy cheap or expensive?" The key is buying to protect, which is a better answer.
This link shows the minimum standards we need in Canada, but the key is what the standard is in your government legislation for your workers: OSH Answers: Safety Footwear
Proper foot safety is important to all of us. Your feet take an enormous amount of punishment in everyday living, not to mention working in a cluttered garage or workshop. It is only common sense to wear footwear fitting for the job. You wouldn't wear sandals outside in the winter, nor would you in a shop.
There are all kinds of styles for the fashion-conscious. There are the ones that look like the typical high-cut safety boots to ones looking like cowboy boots. Then there are the ones that are low-cut standard look-alike shoes. There are even ones that you can use as dress shoes. The important thing is to wear them.
In designing strategies to protect against foot injury, one has to remember the fundamental principle of occupational health and safety: that occupational hazards should be eliminated at the source. The role of personal protective equipment is to minimize exposure to specific occupational hazards, not to eliminate them. Protective footwear does not guarantee total protection.
The best defense against injuries is prevention. A clean workplace is number one on the scale:
- Clear the work floor of any sharp, hot objects that can penetrate your safety footwear.
- Clear any walking paths of any obstacles that can scrape the side of your feet or ankles.
- Avoidance of obstacles can cause twisting or spraining of feet and ankles.
- Safely secure any objects above the floor from falling on your feet.
- Make sure the floor and paths have proper resistance for walking. A newly painted floor can be like layering ice on the floor. Putting sand or other material in with the paint will ensure some resistance to slippage.
All jurisdictions require that workers wear adequate protection against workplace hazards. All working footwear, for both men and women, whether it is safety wear or not, should provide comfort without compromising protective value.
Basic Things to Look for in Buying Safety Footwear
- A steel toe cap should cover the whole length of the toes from tips to beyond the natural bend of the foot. A soft pad covering the edge of the toecap increases comfort. If the toecap cuts into the foot, either the size or style of the footwear is incorrect.
- Soles come in a variety of thicknesses and materials. They need to be chosen according to the hazards and type(s) of flooring in the workplace.
- Uppers of protective footwear come in a variety of materials. Selection should take into account the hazards and individual characteristics of the worker's foot.
- A steel midsole, which protects the foot against penetration by sharp objects, should be flexible enough to allow the foot to bend.
- No one type of non-slip footwear can prevent the wearer from slipping on every surface type.
- Make sure they are a good fit.
There are conditions such as calluses, ingrown toenails, or simply tired feet that are common among workers. Although these may not be considered occupational injuries in the strictest sense, they can have serious consequences for health and safety at the workplace. They cause discomfort, pain, and fatigue. Fatigue sets up the worker for further injuries affecting the muscles and joints. Also, a worker who is tired and suffering pain is less alert and more likely to act unsafely. An accident of any kind may result. A proper fitting boot will also help in good posture and skeletal alignment.
Fit and Care of Safety Footwear
Check the Fit:
- Walk in the new footwear to ensure it is comfortable.
- Boots should have ample toe room (toes should be about 12.5 mm from the front).
- Make allowances for extra socks or special arch supports when buying boots.
- Boots should fit snugly around the heel and ankle when laced.
- Lace up boots fully. High-cut boots provide support against ankle injury. Loose laces can be a hazard in themselves, causing tripping over your own feet or catching on objects in the area.
Footwear Care:
- Use a protective coating to make footwear water-resistant. Inspect and reapply protective coating when necessary. Wet boots often curl near the toe when dried, causing discomfort and abnormal wear.
- Inspect footwear regularly for damage. The soles often crack with age, leaving openings for potential hazards.
- Repair or replace worn or defective footwear.
- Electric shock resistance of footwear is greatly reduced by wet conditions and with wear. Dig out any objects stuck in the sole. They can make the boot a path for electricity and a slippery factor on the floor.
Boot Badges on the Boots
Boot badges will signify the level of safety the boot will have.
Selection of Safety Footwear
Marking Criteria Use
- Green triangle footwear has sole puncture protection with a Grade 1 protective toe (withstand impact up to 125 joules).
- Any industrial or heavy work environment, including construction, where sharp objects are present (such as nails).
- Yellow triangle footwear has sole puncture protection and Grade 2 protective toe (withstand impact up to 90 joules).
- Light industrial work environments that need both puncture and toe protection.
- White rectangle with orange Greek letter "omega" footwear has soles that provide electric shock resistance.
- Any industrial environment where accidental contact with live electrical conductors can occur. (REMEMBER: Electric shock resistance is greatly reduced by wet conditions and with wear)
- Yellow rectangle with green letters "SD" and grounding symbol footwear has soles that are static dissipative.
- Any industrial environment where a static discharge can be a hazard for workers or equipment.
- Red rectangle with black letter "C" and grounding symbol footwear has soles that are electrically conductive.
- For any industrial environment where low-power electrical charges can be a hazard for workers or equipment.
- White label with green fir tree symbol footwear provides protection when using chainsaws.
- For forestry workers and others who work with or around hand-held chainsaws and other cutting tools.
Note 1: The ® symbol indicates the preferred position for the identifying logo or mark of the certifying agency.
Note 2: Labels are on the tongue of the right shoe at ankle height. They may also appear at ankle height on the shoe itself (for electrical protection footwear).
Regards
From Canada, Calgary
Acknowledge(0)Amend(0)
Dear tgpenny, Please note the operative standard in India is IS 15298, which consists of 8 parts. The CSA is the operative standard for Canada, and they are not as stringent in many important aspects as our IS 15298, which is a replica of the renowned EN standard.
Also, please note that no safety footwear can guarantee absolute protection as they fall into the category of a secondary line of defense. The primary defense is prevention.
Regards
From India, Kanpur
Acknowledge(0)Amend(0)
Also, please note that no safety footwear can guarantee absolute protection as they fall into the category of a secondary line of defense. The primary defense is prevention.
Regards
From India, Kanpur
Acknowledge(0)Amend(0)
Thank you very much for your detailed input. Before this, I was not aware of all this. You mentioned that you have a chart with you. Could you please share it? Thanks to everyone for all your contributions to my thread.
Regards,
SSM
From India, Madras
Acknowledge(0)Amend(0)
Regards,
SSM
From India, Madras
Acknowledge(0)Amend(0)
dear mr. chucknoo, thanks for the updates. let me try for the technical sheets of the safety shoes that we are using also. if i get that, i will share the same.
From India, Delhi
Acknowledge(0)Amend(0)
From India, Delhi
Acknowledge(0)Amend(0)
Can anybody differentiate between conductive, ESD, Antistatic & Electrical shock resistant safety footwear ?????? Sudhir Agarwal
From India, Kanpur
Acknowledge(0)Amend(0)
From India, Kanpur
Acknowledge(0)Amend(0)
Types of Safety Boots
Find out exactly what type of safety boots you need. For example, some have a steel toe, while others have the toe reinforced with a stronger fabric.
Also, if you're going to be on the job for a while, consider paying a little extra to get a boot with extra padding. If you'll only be on the job for a month or two, or it's a role where you're not on your feet a lot (e.g., a security guard at a construction site), you'd be okay with a cheaper pair.
From China, Guangzhou
Acknowledge(0)Amend(0)
Find out exactly what type of safety boots you need. For example, some have a steel toe, while others have the toe reinforced with a stronger fabric.
Also, if you're going to be on the job for a while, consider paying a little extra to get a boot with extra padding. If you'll only be on the job for a month or two, or it's a role where you're not on your feet a lot (e.g., a security guard at a construction site), you'd be okay with a cheaper pair.
From China, Guangzhou
Acknowledge(0)Amend(0)
There is nothing like cheap or costly safety footwear if it meets the prescribed standard. There is no difference in the level of protection offered by cheap or costly safety footwear if they are marked with the same safety standard. Safety guards at construction sites are also exposed to risks such as falling and rolling objects, so it is better that they wear steel toe footwear.
From India, Kanpur
Acknowledge(0)Amend(0)
From India, Kanpur
Acknowledge(0)Amend(0)
You have to purchase it from BIS office. Exact standard is IS 15298 part 1 to 8. Part 1 & part 2 will serve your purpose. Its a copyright material.
From India, Kanpur
Acknowledge(0)Amend(0)
From India, Kanpur
Acknowledge(0)Amend(0)
Thank you all for your valuable contribution, which has given me greater insight regarding safety shoes. However, I am still unable to understand some basics. Please let me know what "Density," "Single Density," and "Double Density" mean with respect to safety shoes, a little more elaborately.
Regards,
SSM
From India, Madras
Acknowledge(0)Amend(0)
Regards,
SSM
From India, Madras
Acknowledge(0)Amend(0)
Understanding Sole Density in Safety Footwear
In common parlance, density relates to Direct Injected PU soles. Single density means that the density of the sole is the same throughout. In single-density PU soles, this varies between 0.55-0.7. However, to provide lighter footwear and save on PU cost (PU is priced by Kg), cheaper safety footwear uses an even lower density, such as 0.4. The lower the density, the more abrasion there will be, resulting in quicker wearing of the sole.
Double Density PU Footwear
In double-density PU footwear, the outer shell (outsole), which is around 3 mm thick and in contact with the ground, has a density of 1, while the core or midsole has a density of 0.4-0.45. Double-density soles offer better abrasion resistance and protection, and are costlier than single-density soles. They are more comfortable as the lower density midsole offers a cushioning effect. Sometimes in double-density soles, different materials like TPU (outsole) + PU (midsole) or rubber in the outsole & PU in the midsole are used. Double density in rubber is also available.
I am attaching a photo of the cut section of a double-density PU sole for better understanding.
Regards,
Sudhir Agarwal
From India, Kanpur
Acknowledge(0)Amend(0)
In common parlance, density relates to Direct Injected PU soles. Single density means that the density of the sole is the same throughout. In single-density PU soles, this varies between 0.55-0.7. However, to provide lighter footwear and save on PU cost (PU is priced by Kg), cheaper safety footwear uses an even lower density, such as 0.4. The lower the density, the more abrasion there will be, resulting in quicker wearing of the sole.
Double Density PU Footwear
In double-density PU footwear, the outer shell (outsole), which is around 3 mm thick and in contact with the ground, has a density of 1, while the core or midsole has a density of 0.4-0.45. Double-density soles offer better abrasion resistance and protection, and are costlier than single-density soles. They are more comfortable as the lower density midsole offers a cushioning effect. Sometimes in double-density soles, different materials like TPU (outsole) + PU (midsole) or rubber in the outsole & PU in the midsole are used. Double density in rubber is also available.
I am attaching a photo of the cut section of a double-density PU sole for better understanding.
Regards,
Sudhir Agarwal
From India, Kanpur
Acknowledge(0)Amend(0)CiteHR is an AI-augmented HR knowledge and collaboration platform, enabling HR professionals to solve real-world challenges, validate decisions, and stay ahead through collective intelligence and machine-enhanced guidance. Join Our Platform.
Role of trade unions in ensuring health & safety protection at the Mine.pdf
Ladder Safety Tips.zip
Safety-safetydr iving_111.pps